Water & pools

Water Tank Volume Calculator

Calculate full geometric capacity, partial water volume and unfilled volume from internal tank measurements.

Created and Written by: Designation: Founder

Technically reviewed by: Riya Kulkarni | BE Civil Engineer

Measure the tank interior

Default dimensions are editable arithmetic examples. Use internal dimensions, not exterior measurements or nominal capacity. Geometric capacity is not safe working capacity; confirm operating levels and calibration with the tank supplier.

1. Shape and internal dimensions

Assumes a level tank with constant rectangular or circular cross-section and flat ends. Horizontal-cylinder length is the internal straight length between flat end faces. Diameter is the internal circular diameter. Domed, dished, tapered, tilted or irregular tanks need a different model. Unit selectors retain the numeric entry rather than converting it.

2. Current water level

Measure vertical water depth from the lowest internal bottom. Zero means empty; full depth equals the internal height, or diameter for a horizontal cylinder. The horizontal depth-to-volume relationship is nonlinear. Unfilled volume is geometric space, not a recommended freeboard or a usable reserve.

EXAMPLE · CURRENT WATER VOLUME
1,346.494 US gal

5,097.032 L / 5.097 m³ water volume · US liquid gallons

Full geometric capacity
2,244.156 US gal / 8.495 m³
Current water volume
180 ft³ / 5.097 m³
Water volume in liters
5,097.032 L
Unfilled geometric volume
897.662 US gal / 3.398 m³
Volume filled
60%
Internal vertical depth
5 ft / 1.524 m
Water depth
3 ft / 0.914 m
Unfilled vertical depth
2 ft / 0.61 m

Calculation basis

Rectangular: V=L×W×water depth. Vertical cylinder: V=πD²×water depth/4. Horizontal cylinder: V=L[R²acos((R−h)/R)−(R−h)√(2Rh−h²)], where R=D/2 and h is water depth. Full capacity uses full internal depth. Stable small-segment and complementary calculations handle shallow and nearly full horizontal levels.

No dished heads, wall thickness, obstructions, dead storage, operating freeboard, usable capacity, structural/pressure design, flow, water treatment or calibrated gauge chart. US liquid gallon=231 in³; no Imperial gallon output. Display rounds to 3 decimals; cylinder results use floating-point π/trigonometry after exact decimal dimension checks.

Internal geometry and water level

Use internal measurements for a rectangular tank, a vertical flat-ended cylinder or a horizontal flat-ended cylinder. The calculator reports full geometric capacity, current water volume and unfilled geometric volume. Full capacity is not a recommended operating limit or usable storage rating. Water depth is measured vertically from the lowest internal bottom in a level tank.

Rectangular and vertical-cylinder formulas

For internal length L, width W, full height H and water depth h, a rectangular tank has full volume LWH and water volume LWh. For a vertical cylinder of internal diameter D, full volume is πD²H/4 and water volume is πD²h/4. In these two shapes, the water-volume fraction is h/H because cross-sectional area is constant with height.

Horizontal cylinders fill nonlinearly

For an internal radius R=D/2 and straight internal length L between flat end faces, full cylinder capacity is πR²L. At water depth h from the lowest bottom, water volume is L × [R²acos((R−h)/R) − (R−h)√(2Rh−h²)], with inverse cosine in radians. Half-depth is half-volume; quarter-depth is not quarter-volume. Empty h=0 and full h=2R are handled directly.

The implementation evaluates the smaller lower circular segment and its complement near full depth. A half-angle expression and small-angle series avoid subtracting nearly equal values for very shallow depths. The unfilled small segment is calculated separately near full depth instead of losing it by subtracting two rounded full volumes. Cylinder results still use floating-point π and trigonometry, not arbitrary-precision calibration.

US rectangular example

An internal 10 × 6 × 5 ft rectangular tank has 300 ft³ full capacity. At 3 ft water depth it contains 180 ft³, or 1,346.493506 US liquid gallons and 5,097.03238656 liters. Its unfilled geometric volume is 120 ft³ and its volume fill is 60%. Dimensions are editable arithmetic examples; usable storage may be smaller because of operating limits or equipment.

Metric and horizontal examples

A 2 × 1 × 1 m rectangular tank at 0.75 m water depth contains 1.5 m³, or 1,500 liters, with 2 m³ full capacity. A vertical cylinder of 2 m internal diameter and 3 m internal height contains 1.5π = 4.712388980 m³ at 1.5 m water depth, exactly half its full 3π m³ capacity.

A horizontal flat-ended cylinder of 2 m internal diameter and 4 m straight length has full capacity 4π = 12.566370614 m³. At 0.5 m water depth its volume is 4π/3 − √3 = 2.456739397 m³, approximately 19.5501% full rather than 25%. At 1 m depth it contains 2π = 6.283185307 m³; at 2 m depth it is geometrically full.

Units and validation

All dimensions accept ft, in, yd, m, cm or mm independently. Selectors retain the entered number; select the unit in which that dimension was measured. Results use m³, ft³, liters and clearly labeled US liquid gallons. One US liquid gallon is 231 in³, exactly 3.785411784 liters. Imperial gallons are not displayed.

Positive tank dimensions must be 0.000001–1,000,000 ft equivalent. Water depth may be zero and must not exceed internal height, or diameter for the horizontal orientation. Inputs accept up to 18 decimal places. Full capacity must not exceed one million m³. These are software bounds, not acceptable tank-design limits. Hidden dimensions for inactive shapes are ignored. Exact decimal comparisons validate water depth before numerical cylinder evaluation; displayed values round to three decimals.

What the result excludes

No dished or domed heads, tapered bottoms, wall thickness, internal obstructions, tilted geometry, dead storage, operating freeboard, usable reserve or gauge calibration is inferred. A rounded display of 100% can coexist with a very small unfilled geometric volume. Use the supplier’s tank chart and actual operating limits where measurement accuracy matters. Structural strength, pressure, pumping, flow, treatment and potable-water suitability are not calculated.

Primary references

Wolfram MathWorld: Horizontal Cylindrical Segment gives the circular-segment volume and its empty, half and full cases. The numerical stabilization described here is an implementation choice for that geometry. See NIST SP 811 conversion factors for measurement conversions. References checked 4 November 2026. No supplier endorsement or independent engineering review is claimed.

Related calculations

Use Pool Volume for pool footprints and depths. For current general volume conversion, use Unit Converter.

All calculators

TECHNICAL REVIEWER

Riya Kulkarni | BE Civil Engineer

Riya Kulkarni qualifications and experience
QualificationBE Civil – Shivaji University, Kolhapur (2018)
Experience8+ Years
Technical SpecialisationsStructural Engineering, Construction Materials, Site Execution and Concrete Technology.

Project experience

1. Shree Ganesh Residency

Location: Rajarampuri, Kolhapur

Project Type: G+4 Residential Apartment Building

Technical responsibilities
  • RCC structural construction coordination.
  • Reinforcement and shuttering inspection.
  • Concrete pouring and curing supervision.
  • Monitoring construction materials and workmanship.
  • Site quality-control documentation.

2. Vrindavan Heights

Location: Tarabai Park, Kolhapur

Project Type: G+5 Residential Building

Technical responsibilities
  • Structural drawing interpretation.
  • Reinforcement detailing checks.
  • Concrete workability and placement monitoring.
  • Construction sequencing and site coordination.
  • Building material quality assessment.

3. Sai Krupa Row Houses

Location: Kalamba Road, Kolhapur

Project Type: Residential Row Housing Development

Technical responsibilities
  • Foundation and plinth construction coordination.
  • Brick masonry and plastering inspection.
  • Concrete mixing, placement and curing.
  • Waterproofing and finishing work coordination.
  • Construction progress documentation.

4. Greenview Enclave

Location: Ujalaiwadi, Kolhapur

Project Type: G+3 Residential Apartment Complex

Technical responsibilities
  • Site execution monitoring.
  • RCC work and reinforcement inspection.
  • Construction material management.
  • Concrete quality testing coordination.
  • Workmanship and quality documentation.

5. Lotus Business Plaza

Location: Shahupuri, Kolhapur

Project Type: G+3 Commercial Building

Technical responsibilities
  • Structural construction coordination.
  • Slab and column reinforcement inspection.
  • Concrete placement and quality monitoring.
  • Construction activity sequencing.
  • Contractor and site-team coordination.

6. Omkar Residency

Location: Kadamwadi, Kolhapur

Project Type: G+5 Residential Apartment Building

Technical responsibilities
  • Foundation and superstructure execution coordination.
  • Reinforcement and formwork inspection.
  • Concrete testing and curing monitoring.
  • Material specifications and quality checks.
  • Site inspection reporting.

7. Silver Oak Villas

Location: Kasaba Bawada, Kolhapur

Project Type: Independent Residential Villa Development

Technical responsibilities
  • Residential foundation construction.
  • RCC structural component inspection.
  • Masonry and plastering quality checks.
  • Flooring and finishing coordination.
  • Site execution and material monitoring.

8. Pratham Commercial Complex

Location: Ruikar Colony, Kolhapur

Project Type: Commercial and Retail Building

Technical responsibilities
  • RCC construction coordination.
  • Concrete quality-control procedures.
  • Structural component inspection.
  • Construction material assessment.
  • Execution progress and quality reporting.