Whole-course block takeoff
This estimator counts a single straight retaining wall with uniform height and one block module. Enter installed working length and course height from the chosen system. Exposed block height is measured above grade to the top of the blocks, below any separate cap; add buried block depth from the approved layout. The calculator does not choose embedment, wall height, setbacks or reinforcement.
Formulas and rounding
Target block height = exposed block height + buried depth. Courses = ceil(target height / block course height). Block positions per course = ceil(wall run / working block length). Base blocks = courses × positions per course. Blocks to order = ceil(base blocks × (1 + extra blocks% / 100)). These are full-block equivalents for a conservative straight-run takeoff, not a staggered bond or cutting schedule. No offcuts transfer between courses.
Whole-course height = courses × course height. The difference from the target is shown, not presented as permission to build a taller wall. Final elevations and burial must match the approved project layout. Unit selectors retain numeric entries; they change how the entered number is interpreted rather than converting it automatically. Calculations use exact decimal fractions for ceiling decisions; display rounds to three decimals.
Caps are a separate row
Base caps = ceil(wall run / working cap length). Caps to order = ceil(base caps × (1 + extra caps% / 100)). Cap allowance never increases wall blocks. Cap height is excluded from both height inputs and outputs. Use constant installed coverage along the same straight run; tapered alternating caps, return ends, overhangs and corner cuts need a product-specific takeoff. Leave caps off when they are not a separate product.
US worked example
A 20 ft run with 2 ft exposed block height and 6 in buried depth has a 30 in target block height. A 16 in working block length and 6 in course height require 15 positions per course × 5 courses = 75 base blocks. Ten percent extra gives ceil(82.5) = 83 blocks, including 8 extra. Separate 12 in working caps give 20 base caps; 5% extra gives 21 caps. These dimensions and allowances are editable arithmetic examples, not product recommendations.
If exposed height changes to 25 in while burial stays 6 in, the 31 in target rounds to 6 courses and 36 in of blockwork. There are 90 base blocks and 99 with 10% extra. The 5 in height difference must be reconciled with the approved levels. Blocks already rounded per course cannot be replaced by a single rounded wall-area ratio: a 25 in run and 7 in target with a 12 × 6 in module need 3 positions × 2 courses = 6 full-block equivalents, rather than 3 from an area-only ceiling.
Metric worked example
A 10 m run, 1 m exposed height and 0.2 m buried depth with a 0.5 × 0.2 m working module need 20 positions × 6 courses = 120 base blocks; 10% extra gives 132. Separate 0.4 m caps need 25 base pieces; 5% extra gives 27. No US-to-metric nominal product equivalence is assumed.
Scope and validation
Positive lengths must be between 0.000001 and 1,000,000 ft equivalent; buried depth can be zero. Base block and cap counts are each limited to one million. Separate allowances accept 0–100% with at most four decimal places. These are software bounds, not permitted engineering ranges. Inactive cap entries are ignored. Use separate takeoffs for changes in height or product and reconcile shared corners/end units manually.
This tool does not assess earth pressure, bearing, sliding, overturning, global stability, surcharge, water, frost, seismic loads, permits or engineering requirements. It does not estimate base aggregate, drainage, backfill, geogrid, adhesive, pallets, cost, corners, steps or curves. Follow the product instructions and the site-specific design.
Primary references
Allan Block material estimation worksheet separates block width/course height takeoff and identifies buried block as part of blockwork height. This calculator uses its own explicit whole-course rounding and separate allowances, without adopting a universal burial depth. See NIST SP 811 conversion factors for measurement conversions. References checked 4 November 2026. No manufacturer endorsement or independent engineering review is claimed.
Related calculators
For separate quantities, use Concrete Block, Gravel and Trench Excavation. These estimates do not select a retaining wall design.