Formula and worked example
Steel mass = steel cross-sectional area × length per piece × identical piece count × mass density. Mass per unit length = area × density. Keep area, length and density in consistent units before multiplying. This page uses the common term weight for mass in lb or kg; it does not calculate force.
Default arithmetic example: a flat bar 6 in wide and 0.5 in thick has 3 in² of steel area. Each 10 ft piece contains 360 in³, exactly 0.00589934304 m³. At the editable 7850 kg/m³ density, one piece has a theoretical mass of 46.309842864 kg and two pieces total 92.619685728 kg, approximately 204.191454 lb. No waste or extra stock is included.
Section area formulas
- Plate, flat or square bar: A = width × thickness. For a square bar, enter equal dimensions.
- Solid round: A = π × diameter² ÷ 4. Use full diameter, not radius.
- Rectangular or square hollow section: A = B × H − (B − 2t) × (H − 2t), where B and H are outside dimensions and t is uniform wall thickness. Both inside dimensions must remain positive.
- Angle: A = t × (leg A + leg B − t), where legs are measured outside-to-outside at the heel. The overlap at the corner is counted once. Both legs must exceed the uniform thickness.
- Symmetric I-section: A = 2 × flange width × flange thickness + (overall height − 2 × flange thickness) × web thickness. Two identical flanges are assumed; the web occupies the clear height between them.
- Known area: use verified steel material area from a section table. Do not enter the overall bounding rectangle, a moment of inertia or a section modulus.
Idealized geometry and actual products
Geometric modes assume straight, constant sections with sharp corners and uniform thicknesses. Real rolled sections can have root fillets, rounded corners, tapered flanges and manufacturing tolerances. The hollow rectangle formula does not account for HSS corner radii or actual wall variation. The angle and I-section modes omit radii and fillets. These estimates are not a replacement for manufacturer section tables or a measured delivered mass.
Use verified supplier cross-sectional area with a suitable density when actual section area is available. If a supplier provides a nominal mass per length, that is a separate product quantity and should be used directly for its stated purpose; do not silently treat idealized dimensions as a certified table weight. No holes, cutouts, weld metal, coatings or galvanizing are added or deducted.
Density and US/metric units
The starting density of 7850 kg/m³ is an approximate assumption, not an alloy selection or product guarantee. Verify the value for the actual steel. A shape does not select a grade or density. Density accepts kg/m³ or lb/ft³. The density selector retains the source number, so enter the matching value after choosing units; it does not convert 7850 into an imperial value automatically. Known-area selectors also retain source numbers. Length selectors convert valid entries to 12 significant digits; check converted dimensions before calculating.
One pound equals exactly 0.45359237 kg and one foot equals exactly 0.3048 m. One US short ton is 2000 lb; one metric tonne is 1000 kg. These are separate output units, not interchangeable tons. A rounded 490 lb/ft³ assumption is not exactly equal to 7850 kg/m³; either is used as entered rather than silently replaced with the other.
Independent reference calculations
Metric plate: 200 mm width × 10 mm thickness gives 2000 mm², or 0.002 m². At 7850 kg/m³, mass per length is 15.7 kg/m. Each 6 m piece is 94.2 kg; three pieces total 282.6 kg. At an independently entered 490 lb/ft³, a 6 in × 0.5 in flat bar 10 ft long has mass 102.0833333333 lb per piece, or 204.1666666667 lb for two.
Hollow rectangle: outside 100 × 50 mm with 5 mm walls has steel area 5000 − 3600 = 1400 mm². At 7850 kg/m³ it has 10.99 kg/m; three 2 m pieces total 65.94 kg. Angle: outside legs 100 and 75 mm with 10 mm uniform thickness give 1650 mm² and 12.9525 kg/m; three 2 m pieces total 77.715 kg.
Idealized I-section: 200 mm overall height, 100 mm flange width, 10 mm flange thickness and 6 mm web thickness give 2000 + 1080 = 3080 mm² and 24.178 kg/m at 7850 kg/m³. Two 3 m pieces total 145.068 kg. Solid round: 20 mm diameter has 100π mm² area; a 2 m piece has mass 1.57π kg, approximately 4.932300466 kg. These are arithmetic references without structural approval.
Precision, limits and scope
Reduced decimal fractions preserve geometry, density and unit conversions before display rounding. Round sections use π approximated to 40 decimal places. Display lengths and masses round to three decimals; very small positive results use scientific notation. Theoretical mass is not rounded to packages, stock lengths or truck loads. Piece count is a whole number; the calculator does not optimize cuts.
Positive lengths must be 0.000001–1000000 ft after conversion; steel area must be 0.000000000001–100 m². Piece count is 1–1000000; combined length is limited to 1 billion ft and total mass to 1 billion kg. Density is limited to 1000–20000 kg/m³ after conversion as an input check, not an approved material range. Decimal entries accept up to 18 places. Hidden fields for other section shapes do not affect a calculation.
Use the separate Rebar Weight Calculator for nominal US deformed-bar table masses. Circular pipe outside-diameter/wall calculations and the focused Steel Rod Weight page remain separate requested tools. This calculator does not determine reinforcement requirements, structural strength, connections, deflection, safe lifting or transportation arrangements. Verify final quantities and product data with your project team and supplier.
Reference
SSAB: 20 questions about steel provides an approximate steel density of 7.85 g/cm³, equivalent to 7850 kg/m³, and a rounded imperial reference. Civilable uses this only to explain the editable starting assumption, not as a universal material specification. All section formulas and worked examples above are original geometric calculations.